• MTS Technik koiloveri Stance Gold with front camber plates - Volkswagen PASSAT B2 Variant (33B)
  • MTS Technik koiloveri Stance Gold with front camber plates - Volkswagen PASSAT B2 Variant (33B)
  • MTS Technik koiloveri Stance Gold with front camber plates - Volkswagen PASSAT B2 Variant (33B)
1 3

MTS Technik

MTS Technik koiloveri Stance Gold with front camber plates - Volkswagen PASSAT B2 Variant (33B)

MTS Technik koiloveri Stance Gold with front camber plates - Volkswagen PASSAT B2 Variant (33B)

MTSGWVW112-S

€1.069,00 EUR
€1.069,00 EUR
Akcija Nav noliktavā, raksti siadkracing@gmail.com, lai pasūtītu.
ar PVN. Piegāde tiek aprēķināta apmaksas laikā

MTS Technik Stance coilover kit with Gold housing, with front camber plates, for Volkswagen PASSAT B2 Variant (33B).

SeriesStance
HousingGold
Camber platesfront
Lowering front45 - 85 mm
Lowering rear25 - 95 mm
TÜVno

Specifications

Part number MTSGWVW112-S
Series Stance
Housing Gold
Camber plates / top mounts Front camber plates
Lowering front 45 - 85 mm
Lowering rear 25 - 95 mm
Max. axle load front? max 910 kg
Max. axle load rear? max 1000 kg
Main spring rate GWFE94 (50 N/mm)
GWFE96 (60 N/mm)
Helper spring rate GWHE02 (20 N/mm)
TÜV certificate no

Vehicle fitment

This product fits every vehicle listed below.

?How to check the axle loads of your car
Rating plate

Be sure to check the maximum permissible loads on both axles of your car. This is crucial information! Only if these values are not exceeded, you have a guarantee that the lowering of the car and the operation of the suspension will be consistent with the catalog. You will find this data only on the car's rating plate. The commonly used coding is 1 - XXX kg / 2 - XXX kg, where respectively "1 -" is the maximum permissible front axle load and "2 -" is the maximum permissible rear axle load. Write down these values and compare them with the catalog. If any of them exceed the value from the catalog, it means that the product is not intended for your car.

Vehicle / engine Years · power · drive
1.3 / 1.6 / 1.6 D / 1.6 TD / 1.8 / 1.9 / 2.0 / 2.2
 08/80 - 06/89
40 - 100 kW / 54 - 136 HP
FWD
1.8 Syncro / 2.0 Syncro / 2.2 Syncro
 08/80 - 06/89
66 - 88 kW / 90 - 120 HP
AWD

Features

Eibach springs
Eibach springsCoilover springs made by Eibach, the world leader in the sport springs industry.
Anti-corrosion protection yellow galvanized
Anti-corrosion protection yellow galvanizedDouble zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance.
Top mounts with camber adjustment
Top mounts with camber adjustmentThe camber plates allow the wheel angle adjustment and increase the precision of driving.
2 years warranty
2 years warranty2 year warranty with no mileage limit to confirm high quality.
hexaCOIL adjustable spring perch
hexaCOIL adjustable spring perchInnovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.
Twin-tube construction
Twin-tube constructionThe use of twin-tube technology guarantees stable shock absorber performance.
Gas technology
Gas technologyPressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.
Specially selected type of thread
Specially selected type of threadSpecially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.
High quality
High qualitySuspension components characterized by increased corrosion resistance and made of the highest quality materials.

Product notes

2Front and rear axle height adjustable (threaded shock absorber housing).
9Only for vehicles without NIVO / OEM pneumatic suspension.
21If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.
24During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.
28The kit includes 2 upper front camber plates.
29The installation requires the use of OE front struts - they should be cut and welded as described in the attached manual.
63The adjustment range may be different depending on the vehicle version, the lowering or the accuracy of welding of the suspension components.

Downloads

Skatīt pilnu informāciju