• MTS Technik koiloveri Street Gold - Audi A6 C7 Avant (4G)
  • MTS Technik koiloveri Street Gold - Audi A6 C7 Avant (4G)
1 2

MTS Technik

MTS Technik koiloveri Street Gold - Audi A6 C7 Avant (4G)

MTS Technik koiloveri Street Gold - Audi A6 C7 Avant (4G)

MTSGWAU21

€699,00 EUR
€699,00 EUR
Akcija Nav noliktavā, raksti siadkracing@gmail.com, lai pasūtītu.
ar PVN. Piegāde tiek aprēķināta apmaksas laikā
Front axle load

MTS Technik Street coilover kit with Gold housing for Audi A6 C7 Avant (4G).

SeriesStreet
HousingGold
Camber platesno
Lowering front35 - 65 mm
Lowering rear35 - 60 mm
TÜVyes

Specifications

Series Street
Housing Gold
Camber plates / top mounts Without
Lowering front 35 - 65 mm
Lowering rear 35 - 60 mm
Max. axle load rear? max 1425 kg
Helper spring rate GWHE01 (20 N/mm)
TÜV certificate yes

Versions

Part number Front axle load Main spring rate
MTSGWAU21 max 1170 kg GWFE29VA (90 N/mm)
GWFE55HA (28 - 55 N/mm)
MTSGWAU23 1171-1320 kg GWFE30VA (120 N/mm)
GWFE55HA (28 - 55 N/mm)

Vehicle fitment

All versions fit the vehicles listed below. Choose the version by Front axle load — the permissible axle loads are on the rating plate of your car.

?How to check the axle loads of your car
Rating plate

Be sure to check the maximum permissible loads on both axles of your car. This is crucial information! Only if these values are not exceeded, you have a guarantee that the lowering of the car and the operation of the suspension will be consistent with the catalog. You will find this data only on the car's rating plate. The commonly used coding is 1 - XXX kg / 2 - XXX kg, where respectively "1 -" is the maximum permissible front axle load and "2 -" is the maximum permissible rear axle load. Write down these values and compare them with the catalog. If any of them exceed the value from the catalog, it means that the product is not intended for your car.

Vehicle / engine Years · power · drive
1.8 35 TFSI / 1.8 TFSI / 2.0 TDI / 2.0 TFSI / 2.8 FSI / 3.0 TDI
 05/11 - 11/19
100 - 185 kW / 136 - 252 HP
FWD
2.0 40 TFSI quattro / 2.0 TDI quattro / 2.0 TFSI quattro / 2.8 FSI quattro / 3.0 TDI quattro / 3.0 TFSI quattro
 05/11 - 11/19
140 - 245 kW / 190 - 333 HP
AWD

Features

Eibach springs
Eibach springsCoilover springs made by Eibach, the world leader in the sport springs industry.
Anti-corrosion protection yellow galvanized
Anti-corrosion protection yellow galvanizedDouble zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance.
2 years warranty
2 years warranty2 year warranty with no mileage limit to confirm high quality.
hexaCOIL adjustable spring perch
hexaCOIL adjustable spring perchInnovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.
Twin-tube construction
Twin-tube constructionThe use of twin-tube technology guarantees stable shock absorber performance.
Gas technology
Gas technologyPressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.
Specially selected type of thread
Specially selected type of threadSpecially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.
High quality
High qualitySuspension components characterized by increased corrosion resistance and made of the highest quality materials.

Product notes

3Front and rear axle height adjustable (threaded shock absorber housing on the front, dampers, springs and height adjustable elements on the rear).
21If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.
24During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.
35Rear thread adjustment block is mounted on the top.
73For easier height adjustment, we recommend removing the height adjustment, changing the position of the spring plate and reinstalling the height adjustment on the vehicle.

Notes by version

17Only for vehicles without electronic damping.
Front axle load: max 1170 kg
39Installation is also possible for vehicles with electronic damping force adjustment. The electronic system must be deactivated in this case.
Front axle load: 1171-1320 kg

Downloads

For all versions

For each version

Part number · Front axle load Documents for this version
MTSGWAU21max 1170 kg
PDFSpare part list
MTSGWAU231171-1320 kg
PDFSpare part list
Skatīt pilnu informāciju