MTS Technik

MTS Technik koiloveri Street Gold with front camber plates - Volkswagen JETTA IV (16/AV)

KODS :MTSGWVW91

€769,00 EUR

Akcija Nav noliktavā, raksti siadkracing@gmail.com, lai pasūtītu.

ar PVN. Piegāde tiek aprēķināta apmaksas laikā

Front axle load max 1035 kg 1036-1170 kg

MTS Technik Street coilover kit with Gold housing, with front camber plates, for Volkswagen JETTA IV (16/AV).

SeriesStreet

HousingGold

Camber platesfront

Lowering front35 - 70 mm

Lowering rear30 - 60 mmby version

TÜVno

Specifications

Series	Street
Housing	Gold
Camber plates / top mounts	Front camber plates
Lowering front	35 - 70 mm
Max. axle load rear?	max 1150 kg
TÜV certificate	no

Versions

Part number	Front axle load	Lowering rear	Main spring rate
MTSGWVW91	max 1035 kg	30 - 50 mm	GWFE22VA (32 N/mm) GWFE43HA (43,6 N/mm)
MTSGWVW92	1036-1170 kg	35 - 60 mm	GWFE27VA-01 (34 - 40 - 70 N/mm) GWFE43HA (43,6 N/mm)

Vehicle fitment

All versions fit the vehicles listed below. Choose the version by Front axle load — the permissible axle loads are on the rating plate of your car.

?How to check the axle loads of your car

Be sure to check the maximum permissible loads on both axles of your car. This is crucial information! Only if these values are not exceeded, you have a guarantee that the lowering of the car and the operation of the suspension will be consistent with the catalog. You will find this data only on the car's rating plate. The commonly used coding is 1 - XXX kg / 2 - XXX kg, where respectively "1 -" is the maximum permissible front axle load and "2 -" is the maximum permissible rear axle load. Write down these values and compare them with the catalog. If any of them exceed the value from the catalog, it means that the product is not intended for your car.

Vehicle / engine	Years · power · drive
1.2 TSI / 1.2 TSI 16V / 1.4 TSI / 1.6 / 1.6 MPi / 1.6 TDI / 1.8 TSI / 2.0 / 2.0 TDI / 2.0 TFSI / 2.0 TSI / 2.5	01/08 - 12/19 63 - 155 kW / 86 - 211 HP FWD

Features

Eibach springsCoilover springs made by Eibach, the world leader in the sport springs industry.

Anti-corrosion protection yellow galvanizedDouble zinc plated steel shock absorbers as well as anodized aluminum adjusters and caps to ensure increased corrosion resistance.

Top mounts with camber adjustmentThe camber plates allow the wheel angle adjustment and increase the precision of driving.

2 years warranty2 year warranty with no mileage limit to confirm high quality.

hexaCOIL adjustable spring perchInnovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.

Twin-tube constructionThe use of twin-tube technology guarantees stable shock absorber performance.

Gas technologyPressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.

Specially selected type of threadSpecially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.

High qualitySuspension components characterized by increased corrosion resistance and made of the highest quality materials.

Product notes

3Front and rear axle height adjustable (threaded shock absorber housing on the front, dampers, springs and height adjustable elements on the rear).

21If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.

24During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.

25In some cases it might be necessary to dismount the rear adjustment to achieve the maximum lowering.

35Rear thread adjustment block is mounted on the top.

39Installation is also possible for vehicles with electronic damping force adjustment. The electronic system must be deactivated in this case.

73For easier height adjustment, we recommend removing the height adjustment, changing the position of the spring plate and reinstalling the height adjustment on the vehicle.