• MTS Technik koiloveri Street Inox - Volkswagen SANTANA / PASSAT B2 Saloon (32B) (original struts required)
1 1

MTS Technik

MTS Technik koiloveri Street Inox - Volkswagen SANTANA / PASSAT B2 Saloon (32B) (original struts required)

MTS Technik koiloveri Street Inox - Volkswagen SANTANA / PASSAT B2 Saloon (32B) (original struts required)

XMTSGWVW80

€1.199,00 EUR
€1.199,00 EUR
Sale Sold out
Taxes included. Shipping calculated at checkout.

MTS Technik Street coilover kit with Inox housing for Volkswagen SANTANA / PASSAT B2 Saloon (32B).

SeriesStreet
HousingInox
Camber platesno
Lowering front45 - 85 mm
Lowering rear25 - 95 mm
TÜVyes

Specifications

Part number XMTSGWVW80
Series Street
Housing Inox
Camber plates / top mounts Without
Lowering front 45 - 85 mm
Lowering rear 25 - 95 mm
Max. axle load front? max 900 kg
Max. axle load rear? max 860 kg
Main spring rate GWFE144 (60 N/mm)
GWFE214 (40 N/mm)
Helper spring rate GWHE02 (20 N/mm)
TÜV certificate yes

Vehicle fitment

This product fits every vehicle listed below.

?How to check the axle loads of your car
Rating plate

Be sure to check the maximum permissible loads on both axles of your car. This is crucial information! Only if these values are not exceeded, you have a guarantee that the lowering of the car and the operation of the suspension will be consistent with the catalog. You will find this data only on the car's rating plate. The commonly used coding is 1 - XXX kg / 2 - XXX kg, where respectively "1 -" is the maximum permissible front axle load and "2 -" is the maximum permissible rear axle load. Write down these values and compare them with the catalog. If any of them exceed the value from the catalog, it means that the product is not intended for your car.

Vehicle / engine Years · power · drive
PASSAT B2 Saloon (32B)1.6 / 1.6 D / 1.6 TD / 1.8 / 2.0 / 2.2
05/82 - 06/89
40 - 85 kW / 54 - 116 HP
FWD
SANTANA (32B)1.3 / 1.6 / 1.6 D / 1.6 TD / 1.8 / 1.9 / 2.0 / 2.2
08/81 - 12/85
40 - 88 kW / 54 - 120 HP
FWD

Features

Eibach springs
Eibach springsCoilover springs made by Eibach, the world leader in the sport springs industry.
Stainless steel threaded shock absorbers.
Stainless steel threaded shock absorbers.Stainless steel threaded shock absorbers.
Top mounts with camber adjustment
Top mounts with camber adjustmentThe camber plates allow the wheel angle adjustment and increase the precision of driving.
2 years warranty
2 years warranty2 year warranty with no mileage limit to confirm high quality.
hexaCOIL adjustable spring perch
hexaCOIL adjustable spring perchInnovative hexaCOIL spring perch, significantly increasing the comfort of suspension height adjustment.
Twin-tube construction
Twin-tube constructionThe use of twin-tube technology guarantees stable shock absorber performance.
Gas technology
Gas technologyPressurized gas presses the hydraulic fluid, eliminating the "foaming" effect of the oil (an undesirable and typical for oil shock absorbers phenomenon), which means higher efficiency for continuous, intensive work.
Specially selected type of thread
Specially selected type of threadSpecially selected type of thread and a wide range of suspension adjustment allows optimal setting of the car height.
High quality
High qualitySuspension components characterized by increased corrosion resistance and made of the highest quality materials.

Product notes

2Front and rear axle height adjustable (threaded shock absorber housing).
8Not for 4x4.
9Only for vehicles without NIVO / OEM pneumatic suspension.
21If the vehicle is equipped with a stock sport suspension, the lowering mentioned in this catalogue will be relatively lower.
24During the installation of suspension set the clearance between tire/rim and suspension strut shall be checked. The minimum allowed gap is 5mm (0,2 inch). Otherwise use certificated wheel spacers.
29The installation requires the use of OE front struts - they should be cut and welded as described in the attached manual.
64After the purchase, the original front axle struts should be sent to the headquarters of MTS Technik. Prior to shipment, all elements such as hubs, bearings, covers, shock absorber inserts, bolts and nuts should be dismantled. If the axle struts are delivered without prior disassembly of the above-mentioned parts or if MTS Technik finds any damage, such as broken column bolts, the axle struts will be returned or an additional fee will be charged.
133Available for delivery only within the European Union.

Downloads

View full details